You will need:
Plastic bottle
Ruler
Transparent tape
Scissor
Sunday, 10 July 2011
Saturday, 9 July 2011
How to make a wind vane
You Will Need:
- 1 straw
- 1 straight pin
- 1 index card
- pencil with eraser
- tape
Step One:Cut the point and tail of an arrow out of an index card.
Step two: Tape The Cut out point and the tail and tape it to the straw
Step three: Push the pin through the middle of the straw.
Step Four: Stick the pin into the eraser of the pencil. Make sure the straw can turn freely.
Step Five: Stick Your Completed Work to A Paper plate, Styrofoam Plate Or A Styrofoam Bowl And Your DONE!
Posted by Weatherwhiz 8 at 22:24 0 comments
Thursday, 23 June 2011
More About Wind Vane And Sixs Thermometer
Wind vane
To obtain an accurate reading, the wind vane must be located well above the ground and away from buildings, trees, and other objects which interfere with the true wind direction.
Sixs thermometer
Video about Sixs Thermometer
: http://www.qwiki.com/q/#!/Six%27s_thermometer
Posted by Weatherwhiz 8 at 08:02 0 comments
Six's Thermometer
Six's Thermometer,is also commonly known as a maximum minimum thermometer.It gives three readings: the current temperature, the highest temperature reached since it was last reset, and the lowest temperature reached since it was last reset.It is commonly used wherever a simple way is needed to measure the extremes of temperature at a location.It is commonly used wherever a simple way is needed to measure the extremes of temperature at a location.
The six's thermometer is also places inside a stevenson screen to protect it from the sun rays and
other natural heat radiations.The stevenson screen should be placed 1-2m above ground and away from any bulidings or tall trees that will block it.
Source: http://www.mapsofworld.com/referrals/weather/meteorology/stevenson-screen.html
www.google.com
www.wikipedia.com
Posted by Weatherwhiz 8 at 03:06 0 comments
Wind vane
Wind Vane
A wind vane, also known as a weather vane, is a tool used for determining the direction that the wind is blowing. These instruments have been in use for centuries.They come in many designs, from sleek and professional to ornamentally fun, and can be made at home. Wind vanes are so popular that there even is a dispute about the largest one in the world.
Wind vanes can only measure wind directions a few meters off the ground. The instrument consists of an arrangement of a direction pointer, the two ends of which are known as the "tail" and "nose," pointing toward the direction from where the wind is going and the direction it is coming from, respectively. This is made possible due to the inherent design whereby the smaller area turns into the wind
Making A Wind Vane
Making A Wind Vane
You Will Need
- 2 paper plates
- Scissors
- Poster board
- Plastic straw
- Straight pin
- Pencil with new eraser
- Modeling clay
- Glue
- Compass
- Crayons (optional)
- Styrofoam plate (optional)
Step 1: Write the directions
Write the four directions — east, west, north and south — equally spaced along the outer edges of an inverted paper plate.
Make the project personal by decorating the plate with crayons.
Step 2: Cut shapes
Use scissors to cut an arrow point and an arrow tail from poster board, making each about 2 inches in length.
Cut the shapes from a Styrofoam plate if poster board is unavailable.
Step 3: Make slits in straw
Make small slits at each end of the straw using scissors.
Step 4: Place the shapes
Place one of the poster board shapes into a slit at each end of the straw to create an arrow. This will later point to the direction the wind is blowing.
Step 5: Insert pin
Insert a straight pin through the center of the straw, and then into the eraser tip of the pencil, making sure to leave ample space for spinning at the upper and lower sides of the straw.
Step 6: Set pencil
Set the pencil by pushing its point through the center of the paper plate, and then sticking it into a lump of modeling clay serving as a base.
Test the wind vane by gently blowing it.
Step 7: Place on second plate
Place the structure on a second paper plate, and then glue the plates together with the clay mound inside.
Step 8: Move outdoors
Move the wind vane outdoors after the glue dries, and then align the directions using a compass. Watch the arrow go to work! By learning what type of weather is associated with wind directions in your area, it’s a breeze to forecast conditions.
Video Of Making The Wind Vane
http://www.youtube.com/watch?v=cnZ5LYI19Vo
Posted by Weatherwhiz 8 at 02:06 0 comments
Subscribe to:
Posts (Atom)